CISA + vendors
ICS Advisories
Advisories specifically aimed at industrial control systems — from CISA ICS-CERT and directly from vendors (including Siemens, ABB, Schneider Electric, WAGO and Phoenix Contact) — including revision history (initial publication, Update A, Update B) and linked CVEs.
499
Found
Advisory data: live connection— last retrieved: 20 November 2026 at 22:50.
Filters
499 advisories found
VDE-2020-029
WAGO: XSS vulnerability in Web-UI in WAGO 750-88X and WAGO 750-89X
Risk evaluation
The Web-Based Management (WBM) of WAGOs programmable logic controller (PLC) is typically used for administration, commissioning and updates. The SNMP configuration page of the device is vulnerable for a persistent XSS (Cross-Site Scripting) attack.
Mitigation summary
* Restrict network access to the device. * Use strong passwords * Do not directly connect the device to the internet * Disable unused TCP/UDP-ports
Revision history (3)
Initial publication — 30 September 2020
initial revision
Update A — 10 April 2025
Fixed csaf reference URL
Update B — 14 May 2025
Fix: added distribution
VDE-2021-009
Pilz: Multiple products prone to Niche Ethernet Stack vulnerabilities
Published
20 September 2021
Last update
14 May 2025
Affected sectors
Risk evaluation
Multiple products of PILZ utilise a third-party TCP/IP implementation - the "Niche Ethernet Stack". This TCP/IP stack contains multiple vulnerabilities which are therefore affecting the products listed above.
Mitigation summary
It is adviced to use firewalls or similar network security devices to prevent unauthorized network communication to the products affected.
Revision history (2)
Initial publication — 20 September 2021
Initial revision.
Update A — 14 May 2025
Fix: added distribution
VDE-2020-038
Pepperl+Fuchs: Multiple vulnerabilites in Comtrol IO-Link Master
Published
4 January 2021
Last update
14 May 2025
Affected sectors
Risk evaluation
Several vulnerabilities exist within firmware versions up to and including v1.5.48.
Mitigation summary
In order to prevent the exploitation of the reported vulnerabilities, we recommend that the affected units be updated with the following three firmware packages: - U-Boot bootloader version 1.36 - System image version 1.52 - Application base version 1.6.11
Revision history (3)
Initial publication — 4 January 2021
initial revision
Update A — 12 February 2025
Fix: corrected self-reference, fixed version
Update B — 14 May 2025
Fix: added distribution
Risk evaluation
Pepperl+Fuchs analyzed WirelessHART-Gateways in respect of a critical vulnerability within the Firmware. An attacker may exploit this vulnerability to get access to files and access restricted directories that are stored on the device by manipulating file parameters that reference these. Incoming HTTP requests using fcgi-bin/wgsetcgi and a filename parameter allow a directory / path traversal. A publicly available exploit already exists for this vulnerability.
Mitigation summary
A Firmware (version see table below), which solves the problem, is available. Please contact your support representative for this particular firmware package and update the corresponding product. | Product ID | Version | Bus-Interface of Device | |-----------------|----------|-------------------------| | WHA-GW-*-ETH | 03.00.08 | Modbus | | WHA-GW-*-ETH.EIP | 02.00.01 | Ethernet/IP |
Revision history (4)
Initial publication — 6 March 2019
Initial revision.
Update A — 6 November 2024
Fix: correct certvde domain, added self-reference
Update B — 12 March 2025
Fix: Version, Remediation
Update C — 14 May 2025
Fix: added distribution
VDE-2021-027
Pepperl+Fuchs: WirelessHART-Gateway - Vulnerability may allow remote attackers to cause a Denial Of Service
Published
16 October 2021
Last update
14 May 2025
Linked CVEs
Affected sectors
Risk evaluation
Critical vulnerabilities have been discovered in the product and in the utilized components jQuery by jQuery Team and TLS Version 1.0/1.1. The impact of the vulnerabilities on the affected device may result in - denial of service - remote code execution - code exposure
Mitigation summary
An external protective measure is required. - Minimize network exposure for affected products and ensure that they are not accessible via the Internet. - Isolate affected products from the corporate network. - If remote access is required, use secure methods such as virtual private networks (VPNs).
Revision history (2)
Initial publication — 16 October 2021
Initial revision.
Update A — 14 May 2025
Fix: added distribution
VDE-2021-028
Pepperl+Fuchs: Multiple VDM100-Distance Ethernet-IP sensors with multiple vulnerabilities
Published
16 August 2021
Last update
14 May 2025
Linked CVEs
Affected sectors
Risk evaluation
Critical vulnerabilities have been discovered in the utilized component TRECK TCP/IP Stack by Digi International Inc. For more information see advisory by Digi International Inc.: Digi International Security Notice - TRECK TCP/IP Stack "RIPPLE20" VU#257161 ICS-VU-035787 | Digi International
Mitigation summary
An external protective measure is required. - Minimize network exposure for affected products and ensure that they are not accessible via the Internet. - Isolate affected products from the corporate network. - If remote access is required, use secure methods such as virtual private networks (VPNs).
Revision history (2)
Initial publication — 16 August 2021
Initial revision.
Update A — 14 May 2025
Fix: added distribution
VDE-2021-042
Weidmueller: Remote I/O fieldbus couplers (IP20) affected by INFRA:HALT vulnerabilities
Published
18 October 2021
Last update
14 May 2025
Linked CVEs
Affected sectors
Risk evaluation
The Weidmueller Remote I/O (IP20) fieldbus couplers (u-remote) are affected by several vulnerabilities of the third-party TCP/IP Niche stack. An attacker may use crafted IP packets to cause a denial of service or breach of integrity of the affected products. Weidmueller recommends restricting network access from the internet and also locally to reduce the attack vector to a manageable minimum.
Mitigation summary
Fieldbuses (including Industrial Ethernet protocols) in general are not intended for direct connection with the internet, as they lack a proper set of security capabilities. This also applies to Weidmüller IP20 Remote I/O fieldbus couplers, which are developed and designed for operation in closed industrial networks. - Do not directly connect the affected products to the internet. - Restrict network access to the affected products by proper secured network infrastructure (e.g. routers, firewalls, DMZ, VPNs). - Restrict physical access to the industrial network and affected products (e.g cabinets, seals, closures).
Revision history (3)
Initial publication — 18 October 2021
Initial revision.
Update A — 10 April 2025
Fix: change vendor in product tree
Update B — 14 May 2025
Fix: added distribution
VDE-2020-022
Endress+Hauser: Ecograph T utilizing Webserver firmware version 2.x exposes sensitive information
Risk evaluation
The firmware release has a dynamic token for each request submitted to the server, which makes repeating requests and analysis complex enough. Nevertheless, it's possible and during the analysis it was discovered that it also has an issue with the access-control matrix on the server-side.
Mitigation summary
Customers should configure a perimeter firewall to block traffic from untrusted networks and users to the device. These recommendations will be incorporated into the device documentation (operating instructions) Change default password for operator, service and admin account. Endress+Hauser will not change this behavior. Customers are recommended to take the measures for Temporary Fix / Mitigation as described above.
Revision history (4)
Initial publication — 19 November 2020
Initial revision.
Update A — 6 November 2024
Fix: correct certvde domain, added alias, added self-reference
Update B — 11 April 2025
Fix: version range
Update C — 14 May 2025
Fix: added distribution
VDE-2021-005
Endress+Hauser: Multiple Devices affected by fdtContainer vulnerability
Risk evaluation
The fdtCONTAINER component is integrated into an application (host application). The fdtCONTAINER application is a specific host application which integrates the fdtCONTAINER component. The fdtCONTAINER component exchanges binary data blobs with such a host application. Typically, the host application saves these binary data blobs into a project storage (project file or a project database). To manipulate the data inside the project storage, the attacker needs write access to this project storage. Additionally, the manipulated project needs to be opened by the host application. It depends on the host application whether opening the project requires a user action or not. In fdtCONTAINER applications, the user has to open the manipulated project file manually. In the case of opening a stored project, the deserialization of the manipulated data can be exploited.
Mitigation summary
1. Exchange project data only via secure exchange services 2. Use appropriate means to protect the project storage from unauthorized manipulation 3. Do not open project data from an unknown source 4. Reduce the user rights of the host application to the necessary minimum
Revision history (2)
Initial publication — 1 March 2021
Initial revision.
Update A — 14 May 2025
Fix: added distribution
VDE-2021-044
Endress+Hauser: Multiple products affected by log4net vulnerability
Risk evaluation
Apache log4net versions before 2.0.10 do not disable XML external entities when parsing log4net configuration files. This allows for XXE-based attacks in applications that accept attacker-controlled log4net configuration files.
Mitigation summary
Make sure that no unauthorized access to the production environment is possible. Avoid using the above listed software with Windows administrator privileges if other users with lower privileges have access to the same software installation.
Revision history (3)
Initial publication — 20 January 2022
Initial revision.
Update A — 12 February 2025
Fix: corrected self-reference, fixed version
Update B — 14 May 2025
Fix: added distribution
VDE-2020-031
Endress+Hauser: Multiple products prone to WIBU CodeMeter vulnerabilities
Published
27 October 2020
Last update
14 May 2025
Affected sectors
Risk evaluation
For further Information please refer to WIBU Advisories directly at https://wibu.com/support/security-advisories.html and the aforementioned CVE-IDs.
Mitigation summary
WIBU SYSTEMS has released a new Code Meter Runtime version 7.10a dated on 16.9.2020. All the known vulnerabilities are fixed with this version. The version is available at https://www.wibu.com/support
Revision history (4)
Initial publication — 27 October 2020
Initial revision.
Update A — 6 November 2024
Fix: added self-reference
Update B — 11 April 2025
Fix: version range, remove Issuing authority
Update C — 14 May 2025
Fix: added distribution
Risk evaluation
In case TwinCAT is configured to use the Profinet driver, a denial of service of the controller could be reached by sending special packets to the device.
Mitigation summary
Profinet could be blocked in perimeter firewall to block PROFINET DCP packets from untrusted networks to the device. Beckhoff will provide updates for the mentioned TwinCAT Versions.
Revision history (4)
Initial publication — 9 October 2019
Initial revision.
Update A — 6 November 2024
Fix: correct certvde domain, added self-reference
Update B — 11 April 2025
Fix: version range
Update C — 14 May 2025
Fix: added distribution
vde-2023-002
MB Connect Line: Multiple vulnerabilities in mbConnect24 and mymbConnect24
Risk evaluation
Two vulnerabilites have been discovered in mbCONNECT24 and mbCONNECT24 in all versions through 2.13.3.
Mitigation summary
If you have MFA enabled on the admin user, the password will still be set, but the attacker will be unable to login as the MFA is still in place.
Revision history (2)
Initial publication — 15 May 2023
initial revision
Update A — 14 May 2025
Fix: added distribution
VDE-2022-017
Helmholz: Unauthenticated user enumeration in myREX24 and myREX24.virtual
Risk evaluation
An issue was discovered in myREX24 and myREX24.virtual in all versions through 2.11.2.
Mitigation summary
Update to Version 2.12.1
Revision history (2)
Initial publication — 7 September 2022
initial revision
Update A — 14 May 2025
Fix: added distribution
Risk evaluation
An issue was discovered in the myREX24 and myREX24-virtual software in all versions through V2.9.0.
Mitigation summary
Update myREX24/myREX24-virtual to 2.10.1
Revision history (2)
Initial publication — 8 December 2021
initial revision
Update A — 14 May 2025
Fix: added distribution
Risk evaluation
The data24 service that is bundled with every installation of myREX24 V2/myREX24.virtual has two serious flaws in core components. These combined can lead to a complete loss of confidentiality, integrity and availability.
Mitigation summary
Update to latest version: 2.16.2 CVE-2024-23943: This fix does not apply to REX 200/REX 250 devices with firmware 8.0.0 - 8.1.3. If you are using a device with this firmware, please update it to >= 8.2.0.
Revision history (4)
Initial publication — 18 March 2025
Initial revision.
Update A — 18 March 2025
Update: Changed Product name
Update B — 10 April 2025
Update: fixed CSAF-Reference URL, changed url in credits, removed whitespace after version operator
Update C — 14 May 2025
Fix: added distribution
VDE-2022-057
Wiesemann & Theis multiple products prone to web interface vulnerability
Risk evaluation
Multiple Wiesemann & Theis product families are affected by a vulnerability in the web interface. The device allows an unauthenticated attacker to get the session ID of a logged in user. He may then spoof his IP address to act as the logged in user.
Mitigation summary
Update Com-Server family to version 1.55 Update Com-Server Highspeed family to version 1.78 or higher
Revision history (2)
Initial publication — 13 December 2022
Initial revision.
Update A — 14 May 2025
Fix: added distribution
VDE-2021-007
Pepperl+Fuchs: Multiple Products - Vulnerability may allow remote attackers to cause a Denial Of Service
Risk evaluation
Critical vulnerability has been discovered in the utilized component Ethernet IP Stack by Hilscher Gesellschaft für Systemautomation mbH. The impact of the vulnerability on the affected device is that it can denial of service remote code execution code exposure For more information see advisory by Hilscher: https://kb.hilscher.com/pages/viewpage.action?pageId=108969480
Mitigation summary
An external protective measure is required. Minimize network exposure for affected products and ensure that they are not accessible via the Internet. Isolate affected products from the corporate network. If remote access is required, use secure methods such as virtual private networks (VPNs).
Revision history (2)
Initial publication — 16 February 2021
Initial revision.
Update A — 14 May 2025
Fix: version space, added distribution
VDE-2020-039
TRUMPF: Multiple products prone to WIBU CodeMeter vulnerabilities
Published
27 October 2020
Last update
14 May 2025
Affected sectors
Risk evaluation
A number of TRUMPF CAD/CAM software tools use the CodeMeter Runtime application from WIBU-SYSTEMS AG to manage licences. This application contains a number of vulnerabilities, which enable an attacker to prevent normal operation of CodeMeter, resulting in a Denial-of-Service and potentially execute arbitrary code.
Mitigation summary
- Use the updated versions of the TRUMPF CAD/CAM products that will be available via your service channel shortly. - Until then, reduce internet usage on workstations with TRUMPF CAD/CAM products to a minimum.
Revision history (2)
Initial publication — 27 October 2020
Initial revision.
Update A — 14 May 2025
Fix: reference category, added distribution
VDE-2024-018
Wiesemann & Theis: Multiple products prone to unquoted search path
Risk evaluation
Multiple Wiesemann & Theis software products are affected by a vulnerability through an unquoted search path in the Windows registry. A local attacker can execute arbitrary code and gain administrative privileges by inserting an executable file in the path of the affected product. Update A, 07.03.2024 Incorrect version numbers have been corrected.
Mitigation summary
- Update Com Redirector Legacy external link to version 3.94 or higher (Art.No. 00102) - Update Com Redirector PnP external link to version 4.43 or higher (Art.No. 00111) - Update OPC-Server external link to version 4.89 or higher (Art.No. 00103)
Revision history (3)
Initial publication — 28 February 2024
Initial revision.
Update A — 7 March 2024
Update A
Update B — 14 May 2025
Fix: reference category, added distribution
Risk evaluation
Welotec has closed two vulnerabilities in the TK500v1 router series and advises to update the routers to firmware version r5542 or later. An exploitation of the vulnerabilities can allow an attacker to manipulate the device.
Mitigation summary
Update the product to firmware v2.3.0.r5542 or later.
Revision history (4)
Initial publication — 7 June 2023
initial revision
Update A — 4 June 2024
Minor typo changes. Reorder Products and Branches. Duplicate remediation from document notes to the vulnerabilities.
Update B — 6 November 2024
Fix: correct certvde domain, added self-reference
Update C — 14 May 2025
Fix: firmware category, added distribution, version space
VDE-2020-033
Pilz: Multiple products prone to WIBU-SYSTEMS CodeMeter vulnerabilities
Published
10 September 2020
Last update
14 May 2025
Affected sectors
Risk evaluation
A number of Pilz software tools use the Software CodeMeter Runtime application from WIBU-SYSTEMS AG to manage licences. This application contains a number of vulnerabilities, which enable an attacker to change and falsify a licence file, prevent normal operation of Code- Meter (Denial-of-Service) and potentially execute arbitrary code.
Mitigation summary
Use the current Version 7.10 of the Software CodeMeter Runtime, available via the manufacturer's website. https://www.wibu.com/de/support/anwendersoftware/anwendersoftware.html Only use the Software CodeMeter Runtime as Client. The software tools named under affected products use the Software CodeMeter Runtime as Client in their default setting. Pilz also recommends using a local firewall to limit unwanted access to the network ser- vices of the device with Software CodeMeter Runtime installed.
Revision history (3)
Initial publication — 10 September 2020
Initial revision.
Update A — 6 November 2024
Fix: correct certvde domain, added self-reference
Update B — 14 May 2025
Fix: version space, removed ia, firmware category, added distribution
VDE-2018-016
Pepperl+Fuchs: ecom Mobile devices prone to Android privilege elevation vulnerability
Risk evaluation
An attacker may gain access (by elevated privileges) to CT50-Ex mobile computers through a vulnerability in a system service running the Android Operating System (OS). The system service improperly validates incoming connection requests. Although the vulnerability is significant, currently no known exploits publicly available.
Mitigation summary
An update is available that resolves this vulnerability. All customers using the impacted products should update their products as indicated in the chart below. Only products listed below are affected by this vulnerability. Updates are available via the Pepperl+Fuchs / ecom product support channel or directly from the original manufacturer Honeywell at https://hsmftp.honeywell.com . Pepperl+Fuchs strongly recommends that users upgrade to the version identified below to resolve the vulnerability. CT50-Ex, Android 6.0, Update to CommonES 4.01.00.4134 or later CT50-Ex, Android 6.0, Update ECP to version 2.30.00.0167 or later (if applicable) CT50-Ex, Android 4.4, Update to CommonES 3.17.3445 or later For support, please contact your local Pepperl+Fuchs sales representative.
Revision history (3)
Initial publication — 19 October 2018
Initial revision.
Update A — 6 November 2024
Fix: correct certvde domain, added self-reference
Update B — 14 May 2025
Fix: version space, firmware category, added distribution
VDE-2024-065
PEPPERL+FUCHS: HMI devices are affected by Insecure Platform Key
Risk evaluation
A vulnerability in the use of hard-coded Platform Keys (PK) within the UEFI framework, known as PKfail, has been discovered in several Pepperl+Fuchs devices.
Mitigation summary
Protect the device from unauthorized physical access.
Revision history (2)
Initial publication — 26 November 2024
Initial revision.
Update A — 14 May 2025
Fix: version space
Risk evaluation
A vulnerability has been discovered in the fdtCONTAINER component and application by M&M Software GmbH. As this software is part of the Weidmüller FDT/DTM Software with WI Manager, this Weidmueller software is affected by the above vulnerability as well. The fdtCONTAINER component exchanges binary data blobs with the WI Manager. The WI Manager saves these binary data blobs into a project file. If an attacker gets write access to the project file, the project file can be manipulated to contain malicious code.
Mitigation summary
- Exchange project data only via secure exchange services - Use appropriate means to protect the project storage from unauthorized manipulation - Do not open project data from an unknown source - Reduce the user rights of the WI Manager to the necessary minimum
Revision history (2)
Initial publication — 20 January 2021
Initial revision.
Update A — 14 May 2025
Fix: version space, added distribution